Solved: Possible to increase inactivity Timeout... - Cisco ... Hello All, Cisco IOS: Version 12.4(13r)T Device: Cisco 2821 Is it possible to increase the "inactivity/idle" timeout on the router for when you are telnet'ed in? Right now, after about 10 minutes or so of inactivity you get automatically logged out. Getting error "timeout on slot x port y" on install : PFSENSE Im trying to understand what is needed from this thread, it appears i just need to input these commands: set machdep.disable_msix_migration=1 (press return) set hint.hpet.0.clock=0 (press return) set hint.ahci.0.msi=2 (press return) ahci.0 for channel 0 ahci.1 for channel1 or juste set it for both channels set hint.ahci.1.msi=2 (press return) * boot (press return) Connection Limits and Timeouts - cisco.com † timeout sunrpc hh:mm ss—The idle time until a SunRPC slot is freed. This duration must be at least 1 minute. The default is 10 minutes. ... † timeout sip_media hh:mm ss—The idle time until an SIP media port connection closes. This duration must be at least 1 minute. The default is 2 minutes. The SIP media timer is used used for [Bug 213083] after zpool import ahcich3: Timeout on slot ...
Port vs Slot - What's the difference? | WikiDiff
Boot errors efter upgrade ? | Netgate Forum Hi guys, after upgrade to 2.2.5 it takes unusual long time for boot. 20minutes for full boot up. Ok, to be completely honest, im not sure is this upgrade related problem, because i didnt reboot machine for months. cisco - slot vs sub-slot? - Network Engineering Stack Exchange The x800s also have built-in WIC slots. So if a 2 port serial card is inserted into the first built-in WIC slot, the interfaces are number Se0/0/0 and Se0/0/1. If the second built-in WIC slot is populated with the same 2 port serial card, the numbering is Se0/1/0 and Se0/1/1. The next slot available on an x800 would be the first network module ...
Also we have some recently installed Supermicro X10DRW-i servers with same problems. Such servers were installed to 11.2, so we have no statistic for 11.1 ahci0 ...
No port or ip hit # count (per host) that totaled 10 or below is counted. $src_ip_threshold_value = 0 unless $src_ip_threshold_value; $src_port_threshold_value = 0 unless $src_port_threshold_value; # Set to "on" to have hostnames instead of …
Serial Port Timeout - c-sharpcorner.com
First of i downloaded the tuning calculator on here, entered the dimensions and port size and lengths to obtain my desired frequency tune. But i want the slot port in the center between both subs, and that's where i got confused. Like the calculator says i need to bend the port inside of the box. Solved: Does Petalinux support PCIe - Community Forums
SOLVED New build causing CRC errors and AHCICH timeouts
Port vs Slot - What's the difference? | WikiDiff
Getting error "timeout on slot x port y" on install : PFSENSE Im trying to understand what is needed from this thread, it appears i just need to input these commands: set machdep.disable_msix_migration=1 (press return) set hint.hpet.0.clock=0 (press return) set hint.ahci.0.msi=2 (press return) ahci.0 for channel 0 ahci.1 for channel1 or juste set it for both channels set hint.ahci.1.msi=2 (press return) * boot (press return) python 3.x - a serial port thread in pyQT5 - Stack Overflow The following is my code. I am trying to create a serial port thread in my pyQt5 GUI. I checked many examples. This is very helpful one Background thread with QThread in PyQt. I think I made a successful connection but I am confused about the signature. Coping with the TCP TIME-WAIT state on busy Linux servers